Ready-made answers to the test Fundamentals of facilitation.
Educational institution: SYNERGY, MY, MIT.
Delivery: fresh.
The result of passing 95-100 points (more than 45 questions and answers).
Below you can find questions on the basis of facilitation test.
QUESTIONS TO THE TEST:
1 - Sections that are not part of the section are divided into ...
Response Type: Single Choice
frontal and profile
stepped and broken
rendered and imposed
2 - ... is the image of the visible part of the surface of the object facing the observer
Response Type: Single Choice
cross section
View
Incision
3 - Speaking about the projection of a straight line onto two and three planes, we can say that the straight line is determined by ...
Response Type: Single Choice
a straight line lying in a plane perpendicular to one of the main projection planes
its intersection point with the plane of projections
two points, or one point and direction
a straight line lying in a plane parallel to one of the main projection planes
4 - Dimension and extension lines in the drawing should be done ... with lines
Response Type: Single Choice
solid wavy
solid thick
dash-dot thin
solid thin
5 - The image of an object on several (two or three) combined planes is called ...
Response Type: Single Choice
general arrangement drawing
complex drawing
assembly drawing
6 - Computer-Aided Design (CAD), developed by Autodesk, - ...
Response Type: Single Choice
solidworks
"Compass"
Autocad
7 - Active tools on the status bar in the AutoCAD program are displayed in blue, and inactive ones are ...
Response Type: Single Choice
red
yellow
gray
blocks
8 - Axonometric axes in rectangular isometry are located at an angle to each other ...
Response Type: Single Choice
60°
90°
120°
9 - When filling in the main inscription on the assembly drawing in column 1, under the name of the product, enter: "..."
Response Type: Single Choice
specification
Assembly drawing
Sat
10 - When performing a task according to engineering graphics, it is recommended to take the thickness of a solid main line ...
Response Type: Single Choice
0.5–0.8 mm
0.8–1 mm
1mm
2–5 mm
11 - Set the sequence of stages for the development of product design documentation:
Response Type: Sort
1 working design documentation
2 draft design
3 technical proposal
4 technical project
3,2,4,1
12 - You can build a section of a polyhedron by a plane using two methods: the method of faces and the method ...
Response Type: Single Choice
ribs
planes
projections
14 - ... in AutoCAD is intended for input and options of commands and numerical values that define the parameters of objects
Response Type: Single Choice
Command line
Navigation bar
Profile setup
blocks
15 - Option that allows you to edit the dimension text on the command line and in the numeric field in AutoCAD is "..."
Response Type: Single Choice
MText
linear
Text
Turned
16 - Tool in AutoCAD to create the same or similar objects - "..."
Response Type: Single Choice
fields
layers
sheets
blocks
17 - A drawing made without the use of drawing tools and precise compliance with the scale, – …
Response Type: Single Selection
Assembly Drawing
Specification
Sketch
18 - In AutoCAD, to call the linear size, enter in the command line: "..."
Answer type: Single choice
linear
size
linear size
19 - In the specification, recording within each group is carried out in …
Answer type: Single selection
in ascending order of standard designations
in ascending order of the main parameters or dimensions of the product
in alphabetical order of product names
20 - The template in the AutoCAD program is characterized by an extension …
Response Type: Single Choice
*jpg
*pdf
*dwt
*dwg
21 - The main inscriptions on the design documents are located in the ... corner
Answer Type: Single choice
top right top
left
bottom right bottom
left
22 - ... is a smooth transition from one line to another
Response Type: Single Choice
Curve
Pairing
Polyhedral surface
Scan
23 - Geometric shapes from which you can build t
31 - Изделие, изготовленное из однородного материала без применения сборочных операций, но с применением сварки, спайки, спаивания, – это …
Тип ответа: О
24 - ... is a set of documents containing fundamental design solutions that give a general idea of the device and the principle of operation of the product
Response Type: Single Choice
Technical project
Preliminary design
Technical proposal
Working technical documentation
A 25-text design document that defines the composition of the assembly unit and design documentation is called …
Response Type: Single selection
by Assembly drawing
by Specification
by part drawing
26 - Descriptive geometry is taught in Russia from the first half …
Response Type: Single Choice
XVIII .
XIX century .
XX in
27 - A regular four – sided pyramid is …
Answer Type: Single Choice
Tetrahedron
Octahedron
Icosahedron
30 - The products in the specification for the assembly drawing are recorded in the section "..."
Response Type: Single Choice
Complexes
Kits
Standard products
31 - A product made of a homogeneous material without the use of assembly operations, but with the use of welding, soldering, soldering, is …
Response Type: About
Attention! All tests with ready-made answers may change in the educational institution itself, several questions may change, or the entire test as a whole. It often happens that the tests do not change for years. It all depends on the new teachers who took the initiative to update the questions, so We do not bear any guarantee of 100% passing any test, you can pass it for 60 points, 100 or not at all in case of new questions.
In the description, we indicate our own scores for passing a certain test, which we took ourselves, but as we said above, the questions may vary depending on the educational institution.
No feedback yet